Screen Wall System - R Channel Mount | Connecticut Screen Works

Home • Dealers Wanted • Contact • Photos • Map
Screen Wall Premier Simplicity Self Storing Raw Goods Dealers
Porch Screens - Porch Enclosures Screen Panels - Screen Wall Information Links... Please Select: SCREEN WALL MAIN PAGE ARCHITECTS & DESIGNERS BUILDERS & TRADESMAN DO-IT-YOURSELFER'S POWDER COAT FINISHES METALIZED FINISHES ANODIZED FINISHES MILL FINISH R CHANNEL USAGE PAGE MANUFACTURING OPTIONS PORCH PROJECT HELP INSERTS GET QUOTE Installation Suggestions... Proper planning is essential for trouble free installation. Installation of this system can be performed by most skilled persons. A general home improvement contractor will have no problem. Please Select: ANGLE STOP MOUNT BASE R CHANNEL MOUNT SMALL STOP MOUNT LARGE STOP MOUNTS STANDARD FACE MOUNT OTHER These are by no means all possibilities for installation. Not all mounts we show may work in your situation - in fact, you may find that none do. You may need to utilize a combination of methods or design your own based upon your requirements. Need Samples ?... You can order product line samples right through our web store. Material samples are free of charge. (We do ask that you cover shipping costs) For a minimal charge we can also provide sample sized manufactured panels. Order Samples > WEB STORE Use the "Samples" link located on the left side of web store pages. Be a Fan on Face Book... Made in USA... The Connecticut Screen Works Screen Wall System^® is 100% USA made. Designed and Manufactured exclusively by Connecticut Screen Works, Inc. - Patents Pending -	Quality, Strength and Durability are Standard^TM R Channel Mount... MOUNTING LOCATION: Over Opening CAN INSERTS BE USED: Yes The R CHANNEL MOUNT is a good installation method when openings are out of dimension by no more than 3/4" or when openings are not out of dimension at all. The "R" CHANNEL is utilized as an expander and a mounting flange at the same time. This method can be used with both Panels and Walls with little trouble in most cases. The details below shows mounting from both the exterior and from the interior. Spline channel on Master Frame always faces outward. This mounting method will allow the use of inserts. This method entails the installation of our "R" CHANNEL on all sides of the Panel or Wall. The unit is then secured in place by securing the outer flange of the "R" CHANNEL to the structure. The Master Frame is actually placed inside of the opening when installed but the mounting flange will remain on the exterior or interior dependent upon mounting location. MAJOR RESTRICTIONS & NOTES: It is highly recommended that sufficient help is available during installation to lift and hold Panel(s) or Wall(s) in place until they can be fully mounted to structure. The "R" CHANNEL may be used to cover panel seams when panels are installed within 3/8" of each other (this will provide a clean finish) or if your opening requires the installation of more than 1 panel to cover an opening. See "R" CHANNEL INSTRUCTIONS for details. .pdf VERSION Measuring... Measuring for the "R" Channel Mount can be a little confusing. 1) Measure each opening height and width. Measure in several locations (top, middle, bottom, left side, center, right side, etc.) and record all measurements taken. (To help, you may find it better to draw out each opening and note the measurements and locations taken) 2) Compare the smallest and largest sizes for each openings width and height. 2A) If there is more than 3/4" in difference between the smallest and largest width measurements -or- more than 3/4" in difference between the smallest and largest height measurements you'll need to square up the opening and reduce this difference to less than 3/4" in each. (There is no play here, more than 3/4" in difference will result in not enough mounting flange remaining for installation) 2B) If there is less than 3/4" in difference between the smallest and largest measurements continue to step 3. 3) Subtract 1/4" from the smallest width and 1/4" from the smallest height measurements found for each opening. (The 1/4" reduction provides for 1/8" of clearance on each side of the panel which will be needed for installation) 4) The resulting sizes would be your true manufacture size for each panel or wall being ordered. Plan carefully if you modify this installation since very little room for error exists. Very Important... In all cases, your submitted sizes are to be True Manufacture Sizes (TTT production sizes) required. We do not modify order sizes. Also, all information and directions provided by CSW, Inc. should be treated as generic guides which are intended to help you plan, measure and order screens. Our directions are applicable and correct for a great majority of situations - but not all. In some situations they may need to be modified. In some situations they may not be applicable at all. The responsibility to determine this and the responsibility to order items correctly rests solely on the customer. We make no guarantee, warrantee or promise of any kind that the directions (guides) we provide will work in every application. Please read and understand all information provided on this web site. For additional information please review our POLICIES page fully. Installation... Proper planning is essential for trouble free installation. Installation of this system can be performed by most skilled persons. A general home improvement contractor will have no problem. How to Obtain a Quote... Our staff will be happy to work up a project budget or quotation for you. We would prefer that your submission be by fax or mail utilizing our prepared quote request form. This will ensure that all aspects of your projects costs will be properly accounted for. QUOTE REQUEST FORMS REQUEST QUOTE ON-LINE You may also submit project plans for review. Our staff will review for pricing purposes only - not accuracy or completeness. Our staff will follow our order standards if you are silent on any issue. How to Order Manufactured Products... Manufacture orders must be in writing. You can place your manufacture order with us as follows: By submitting a written order by fax or mail utilizing our prepared order form. FAX OR MAIL ORDER FORMS By executing a non-expired quotation. How to Order Raw Materials... You may order raw materials as follows: On line: WEB STORE By submitting a written order by fax or mail: FAX OR MAIL ORDER FORMS By submitting a quote request by fax, mail, or on line and executing our issued quote: QUOTE REQUEST FORMS REQUEST QUOTE ON-LINE

Connecticut Screen Works, Inc. © 2010 Home \| FAQs \| Policies \| Contact \| Feedback \| Warranty